Skip to content
Image to embroidery

Image to DST converter

To convert an image to DST, upload any common picture format, set the thread color count and hoop, and download the DST. The converter removes the background, reduces the picture to flat thread colors, fits the design inside the hoop and writes stitches at true millimeter size, so density stays correct.

By The Stitchquill team (Machine embroidery and cut-file workflow). Last updated .

Convert

PNG, JPG, JPEG, WEBP, GIF, BMP, TIF, TIFF, PDF, SVG up to 25 MB

How to convert an image to DST, step by step

  1. Upload the picture in whatever format you received it: PNG, JPG, WEBP, GIF, BMP, TIFF, PDF or SVG.
  2. Pick the color count and hoop size.
  3. Read the size line under the preview; it tells you the finished width and height in mm and inches.
  4. Download the DST, or switch to PES, JEF, EXP or VP3 without uploading again.
Example

Image to DST tested with a real logo

We ran our own four-color badge through this exact converter. The picture shows the preview it returned. The numbers come from the same run, so you can compare them with your own file. For example, the badge has a ring, a sun, two peaks and a band, like a typical shop logo.

Image to DST result: preview of a four-color badge
Output preview from our Image to DST test run
Test file
PNG, 800 x 800 px, four colors on white
Output
DST
Finished size
90 x 90 mm
Hoop it fits
4 x 4 in
Stitches
6,823
Thread colors
4
Trims
24
File size
22 KB
Processing time
0.3 s

How we test: we check every page with the same badge, then we read each output back with pyembroidery or open it as a vector. More on the about page.

Why the hoop comes first

A stitch file that is resized after it is written keeps the same number of stitches, so every stitch and every row gap grows or shrinks with it. Embroiderers learn to never resize a design by more than about 20 percent for exactly that reason.

The converter avoids the problem by fitting the artwork to the hoop before a single stitch exists. Row spacing is set at 0.4 mm and stitch length at up to 3 mm on the final geometry, so the density you download is the density you sew.

Pictures that work and pictures that do not

Flat artwork with a few solid colors converts well: logos, mascots, lettering converted to shapes, simple icons. Photos, watercolors and anything with soft shading turn into posterized regions and use far more stitches than they deserve.

If the design would end up narrower than 5 mm on its short side, the converter refuses and tells you the size it reached. A file that fits the hoop but has lost all its detail is worse than no file.

Reading the stitch count

The stitch count under the preview is the number most shops quote from. With this engine's settings, a solid 90 mm circle comes out at about 7,100 stitches, and a flat two-color logo 90 mm wide and 30 mm tall at about 2,700. If your number is much higher than a design like yours should need, a large solid area is probably being filled that could be left as fabric.

Trims matter too. Every trim is a pause on the machine, so a design with dozens of small separate islands sews slower than its stitch count suggests. Merging tiny details or dropping them from the embroidered version shortens the run.

Image and DST compared

File formats involved in this conversion
FormatFull nameUsed byStores colorsWhat is inside
ImageAny image (PNG, JPG, WEBP, GIF, BMP, TIFF, PDF, SVG)Any design or cutting softwareYes, as fill colorsWhatever the customer sent. Every common image type goes through the same trace.
DSTTajima DST stitch fileTajima and most commercial multi-needle machines (Ricoma, SWF, Happy and others)No. Only color stops are stored; you assign threads at the machine.A list of needle moves in 0.1 mm steps with jump, trim and color-stop records, plus a 512-byte header holding the stitch count and design extents.

Hoop sizes and the sewable field

The converter fits each design inside the sewable field, which is the stated hoop size minus 5 mm on each side. So a design sized for 4 x 4 sews on every machine in this table.

Standard hoops the converter targets
HoopStated sizeSewable field usedExample machines
4 x 4 in100 x 100 mm90 x 90 mmBrother SE600, SE700 and PE535, plus most entry-level combo machines
5 x 7 in130 x 180 mm120 x 170 mmBrother PE800, PE900 and SE1900
6 x 10 in160 x 260 mm150 x 250 mmBrother NQ1700E and other mid-range machines
8 x 8 in200 x 200 mm190 x 190 mmJanome Memory Craft 400E class (7.9 x 7.9 in field)
8 x 12 in200 x 300 mm190 x 290 mmLarge-field home and commercial flats; check your hoop's stated field

What the stitch engine produces

Stitch engine settings and limits
SettingValue
Fill density0.4 mm row spacing (tatami), brick-staggered stitch ends
Fill stitch lengthup to 3.0 mm
Underlayperpendicular rows every 2.0 mm, inset 0.5 mm
Thin shapes (under about 1.2 mm)running stitch along the outline, 2.0 mm stitches
Trimsadded for any travel longer than 7 mm, with tie-in and tie-off stitches
Hoop clearance5 mm kept free on every side
Smallest design5 mm on the short side (smaller is refused, not charged)
Upload limit25 MB; PNG, JPG, WEBP, GIF, BMP, TIFF, PDF, SVG
Typical processing timeunder 3 seconds for a 5x7 logo

The engine does not make satin columns, pull compensation or per-fabric density changes. For fine lettering or premium garments, refine the file in digitizing software or hire a digitizer instead.

Questions

Image to DST FAQ

Which image formats can I convert to DST?

PNG, JPG and JPEG, WEBP, GIF (first frame), BMP, TIFF, PDF (first page) and SVG, up to 25 MB.

What is the default hoop?

4 x 4 inches (100 x 100 mm), because it is the most common home machine field. A design fitted to 4 x 4 sews on nearly every machine.

How long does conversion take?

A typical 5 x 7 logo takes under three seconds.

Are my images stored?

No. Uploads are processed in memory and discarded when the response is sent.

Sources and references