Skip to content
Image to embroidery

Convert a logo to an embroidery file

To convert a logo to an embroidery file, upload the logo, pick your machine's format (DST, PES, JEF, EXP or VP3), type the finished width in millimeters, and download. A left chest logo is typically 75 to 100 mm wide and a cap front about 50 to 60 mm tall, and the converter stitches at exactly that size.

By The Stitchquill team (Machine embroidery and cut-file workflow). Last updated .

Convert

PNG, JPG, JPEG, WEBP, GIF, BMP, TIF, TIFF, PDF, SVG up to 25 MB

How to convert a logo to an embroidery file, step by step

  1. Upload the logo in the best format you have: SVG or PDF first, then PNG, then JPG.
  2. Choose your machine's file format.
  3. Enter the finished width, for example 90 mm for a left chest.
  4. Check that small text is still at least 4 mm tall in the preview.
  5. Download and test on the actual garment fabric.
Example

Logo to embroidery file tested with a real logo

We ran our own four-color badge through this exact converter. The picture shows the preview it returned. The numbers come from the same run, so you can compare them with your own file. For example, the badge has a ring, a sun, two peaks and a band, like a typical shop logo.

Logo to embroidery file result: preview of a four-color badge
Output preview from our Logo to embroidery file test run
Test file
PNG, 800 x 800 px, four colors on white
Output
DST
Finished size
90 x 90 mm
Hoop it fits
4 x 4 in
Stitches
6,823
Thread colors
4
Trims
24
File size
22 KB
Processing time
0.3 s

How we test: we check every page with the same badge, then we read each output back with pyembroidery or open it as a vector. More on the about page.

Common logo sizes for an embroidery file

Left chest logos on polos and work shirts usually land between 75 and 100 mm wide. Cap fronts are limited by the crown height, so about 50 to 60 mm tall is typical. Full backs and jacket panels need large hoops and are better digitized by hand.

Enter the width in millimeters and the converter fits the design to exactly that width, unless it would exceed the hoop, in which case it fits the hoop instead and says so.

Simplify before you stitch

Logos designed for screens often contain thin outlines, drop shadows and gradients. At 90 mm wide those details are smaller than a stitch can express. Removing the shadow and thickening outlines to at least 1.5 mm will do more for the sew-out than any setting.

Small taglines under a logo are the most common failure. If the letters end up under about 4 mm tall, drop the tagline from the embroidered version.

Choosing thread colors for a brand logo

Brand colors are usually specified as Pantone or hex values. Thread charts from every major brand publish close matches, so look up the nearest thread for each brand color before the run. The preview shows the colors detected in the artwork, which is a good starting point if no brand guide is available.

On dark garments, a logo designed on white often needs a color swap: a black element disappears on a black cap. Swap it for white or gray thread rather than changing the file.

Image and DST compared

File formats involved in this conversion
FormatFull nameUsed byStores colorsWhat is inside
ImageAny image (PNG, JPG, WEBP, GIF, BMP, TIFF, PDF, SVG)Any design or cutting softwareYes, as fill colorsWhatever the customer sent. Every common image type goes through the same trace.
DSTTajima DST stitch fileTajima and most commercial multi-needle machines (Ricoma, SWF, Happy and others)No. Only color stops are stored; you assign threads at the machine.A list of needle moves in 0.1 mm steps with jump, trim and color-stop records, plus a 512-byte header holding the stitch count and design extents.

Hoop sizes and the sewable field

The converter fits each design inside the sewable field, which is the stated hoop size minus 5 mm on each side. So a design sized for 4 x 4 sews on every machine in this table.

Standard hoops the converter targets
HoopStated sizeSewable field usedExample machines
4 x 4 in100 x 100 mm90 x 90 mmBrother SE600, SE700 and PE535, plus most entry-level combo machines
5 x 7 in130 x 180 mm120 x 170 mmBrother PE800, PE900 and SE1900
6 x 10 in160 x 260 mm150 x 250 mmBrother NQ1700E and other mid-range machines
8 x 8 in200 x 200 mm190 x 190 mmJanome Memory Craft 400E class (7.9 x 7.9 in field)
8 x 12 in200 x 300 mm190 x 290 mmLarge-field home and commercial flats; check your hoop's stated field

What the stitch engine produces

Stitch engine settings and limits
SettingValue
Fill density0.4 mm row spacing (tatami), brick-staggered stitch ends
Fill stitch lengthup to 3.0 mm
Underlayperpendicular rows every 2.0 mm, inset 0.5 mm
Thin shapes (under about 1.2 mm)running stitch along the outline, 2.0 mm stitches
Trimsadded for any travel longer than 7 mm, with tie-in and tie-off stitches
Hoop clearance5 mm kept free on every side
Smallest design5 mm on the short side (smaller is refused, not charged)
Upload limit25 MB; PNG, JPG, WEBP, GIF, BMP, TIFF, PDF, SVG
Typical processing timeunder 3 seconds for a 5x7 logo

The engine does not make satin columns, pull compensation or per-fabric density changes. For fine lettering or premium garments, refine the file in digitizing software or hire a digitizer instead.

Questions

Logo to embroidery file FAQ

What size is a left chest logo?

Usually 75 to 100 mm (3 to 4 inches) wide.

Will this logo embroidery file sew on a cap?

Yes, for flat logos. Structured caps benefit from center-out sequencing that hand digitizers add, so run a test first.

Which embroidery file format fits my logo?

DST for commercial machines, PES for Brother and Baby Lock, JEF for Janome, EXP for Bernina and Melco, VP3 for Husqvarna Viking and Pfaff.

Can I use a customer's logo?

Only with their permission, and trademarked logos need the owner's approval for merchandise.

Sources and references